FullAXS™ connector compatible cable assemblies

FullAXS™ connector compatible cable assemblies             IP-67 water and dust seal over LC Duplex, MTP/MPO and other connector types. Applications include connection to Remote Radio Units (RRU/RRH), FTTA equipment and…

7 Likes Comment

Hand-held Fiber Test Instruments 60 dB Variable Single-mode Attenuation JW3303

Hand-held Fiber Test Instruments 60 dB Variable Single-mode Attenuation JW3303 designed for optimal flexibility and field usability continuously variable optical signal attenuation.                 Features of Optical Variable Attenuator JW3303 Stepwise attenuating…

11 Likes Comment

Hand-held Fiber Test Instruments PON Optical Power Meter JW3213N

Hand-held Fiber Test Instruments PON Optical Power Meter JW3213N is one of PON hand-held fiber optic test instrument widely used at the FTTX installation and maintenance. JW3213N PON Optical Power Meter is to simultaneously test…

9 Likes Comment

HDPE microduct straight connectors

HDPE microduct straight connectors use for connect the HDPE tube , microduct connect , direct buried non sealed or sealed applications

18 Likes Comment

Cable suspension- three-bolt clamps

Cable suspension- three-bolt clamps are used with through bolts to support cable at poles. Through bolt also serves as clamping member. One or more nuts and/or washers are used between the pole and clamp for required…

17 Likes Comment

OTDR fiber rings SCAPC

OTDR Launch Cables and Fiber Rings SC/APC to SC/APC minimize the effect of OTDR dead zone

10 Likes Comment

Tube distribution closure TDC

Tube Distribution Closure for microtube solutions

11 Likes Comment

Fiber optic Lauch leads SC

OTDR fiber optic launch box is the OTDR test extension line for test the blind area

10 Likes Comment

Cable clamp for FTTH ADSS cables ACADSS8

FO figure of 8 cable clamp, steel or FRP Messenger reinforced Ø 8 – 10mm

14 Likes Comment

FTTH FIGURE 8 Anchoring clamp AC68L260

Overview Minimum breaking strength 300 daN. 260/360mm bail. Figure of 8 FO cable dead end with steel or dialectric messenger plus (HDPE) outer sheath. When the cable is fully tensioned, the wedges move further down…

12 Likes Comment

Inflatable Duct Sealer

IDSS-100 Inflatable duct sealing system wraps around cables in the ducts of manholes or exchange vaults. The product effectively seals telephone cable ducts, stopping or preventing water from leaking into the manhole or vault.

7 Likes Comment

AGC FTTH CATV fiber optic mini receiver node WDM

CATV FTTH Optical Fiber Mini receiver high output level with WDM

13 Likes Comment

Fiber optic connector inspection and cleaning kit TW750C

TW750C Optic Fiber Inspection & Cleaning Kit provides a selection of fiber optic cleaning products for use on fusion splice prep, connector endfaces on jumpers and through bulkhead adapters. Both wet and dry cleaning products are offered to effectively prepare fusion splicing, clean connectors, maximizing network performan

10 Likes Comment

Fiber optic cable Demarcation enclosure FTB01E

Fiber optic cable Demarcation box FTB01E suitable for 1 drop cable.

15 Likes Comment

1U closing horizontal cable organizer shunting panel

1U closing horizontal cable organizer shunting panel made in ABS material. OEM and logo service is possible.

7 Likes Comment

Fiber optic accessories

Fiber optic accessories ,Fiber splicing accessories also been know as  Fiber Enclosure Accessories .Usually included Fiber Splice Trays and Fiber Splice Sleeves‎.Fiber Optic Splice  Trays(6cores types ,12cores types,24cores types,48cores types,).most install in the fiber optic distribution box and fiber optic enclosurers.To splice the fiber optic cable and the Splice Protection Sleeves.Heat Shrink Fiber Fusion Splice Protection Sleeves will protect the fiber cables.Networks 60MM Fiber Optic Fusion Splice Protection Sleeve is the most popular Splice Protection Sleeves.Fiber optic sleeves types are :40mm,45mm,50mm,55mm,60mm.

Designed by the continuing cross-linked polyolefin, hot fusion tubing and stainless steel wire composed of fiber protection elements.

1. does not affect the characteristics of the fiber light guide.

2. Protect and improve the mechanical strength.

3. Simple operation, reduce the risk of fiber damage during installation.

4. The transparent casing, so that the fiber connection status at a glance.

5. The sealing structure makes the connection with good resistance to temperature and humidity performance.

6. Working temperature -55-105 ℃, shrinkage temperature range of 90-120 ℃.